Skip to content

Winter 2026 Streaming windows now = black mould by January. Stop condensation in 9 steps

Boiler Symbols Meaning: What the Icons on Your Boiler Display Are Telling You

The radiator, tap, flame, snowflake and spanner symbols on a boiler display explained, including the flashing ones that are normal and the ones that mean a fault.

Alex Morgan avatar
Founder & editor
Published 6 min read
Close-up of a modern combi boiler control panel with small radiator, tap and flame icons lit on its display

Most boiler display symbols just tell you what the boiler is doing. The radiator icon means central heating, the tap icon means hot water, and a flame means the burner is lit right now. A snowflake usually means frost protection or that heating has been switched off for summer. A spanner or a warning triangle means a fault or a service reminder, and normally comes with a code. Flashing radiator or tap icons are usually normal: the boiler is responding to a demand for heat. Exact meanings vary by brand, so check the user guide for your model.

Boiler makers use similar icons, but not identical ones, and the same symbol can mean slightly different things across Worcester Bosch, Vaillant, Ideal and Baxi. The table below covers the common ones. If your display is showing a code as well, our Vaillant fault code list, Worcester reset guide and Baxi E1 guide explain the most common ones. More help is on our heating hub.

Common boiler symbols and what they mean

SymbolUsual meaningNormal or a problem?
RadiatorCentral heating is switched on, or heating demandNormal
Radiator flashingThe boiler is heating the radiators right now (on many models)Normal
TapHot water is switched on, or demand for hot waterNormal
Tap flashingHot water is being heated right now (on many models)Normal
FlameThe burner is litNormal
Flame with a line or cross through itIgnition failure or flame loss lockoutProblem: check gas, then reset
SnowflakeFrost protection active, or heating off (summer mode)Normal
SpannerService due, or a fault code to readAct: check the code
Warning triangle or exclamation markFaultAct: check the code
Reset symbol (circular arrow)Press reset to clear a lockoutProblem: find out why it locked out
ThermometerTemperature setting or current water temperatureNormal
Bar or gauge symbol, or "P"Water pressure readingCheck it's 1 to 2 bar when cold
Eco or leafEconomy mode (often turns off combi preheat)Normal
ClockTimer or programme activeNormal
Chimney or "service" iconService/test mode for engineersShouldn't normally be on

Radiator and tap symbols

These are the two you'll see most. On many boilers, a steady radiator or tap icon means that function is switched on, and it flashes when the boiler is actively heating it. On some Ideal boilers, a cross over both icons means the boiler is switched off, and the word "On" or "Ready" under them shows they're enabled.

A radiator icon on with the heating off often confuses people. On many combis it just means central heating is enabled at the boiler; whether the radiators actually come on is up to your timer and room thermostat.

Finger pointing at a radiator icon on a combi boiler display
A steady radiator icon usually means heating is enabled; flashing usually means it's running now.

Flame symbol

A flame means the burner is lit and gas is burning. It should come and go as the boiler fires and stops. If you see a flame with a cross or a line through it, or a flame plus a warning, the boiler tried to light and failed, or lost its flame. That's a lockout. Check the gas supply (does the hob light?), check the condensate pipe isn't frozen in cold weather, then press reset once. Our Vaillant F28 guide and L2 code guide go through these checks.

If you can smell gas, don't press reset or use switches. Call the National Gas Emergency number on 0800 111 999, turn the gas off at the meter if it's safe to do so, and open the windows.

Snowflake symbol

The snowflake usually means one of two things:

  • Frost protection. The boiler is running briefly to stop itself or the pipes freezing. It may appear on cold nights even with the heating off. Normal.
  • Heating switched off (summer mode). On some boilers, including Worcester Bosch models with a heating dial, turning the dial to the snowflake turns central heating off and leaves hot water only.

If your radiators aren't coming on in winter, check the heating dial isn't turned to the snowflake.

Spanner and warning symbols

A spanner usually means one of two things: a service reminder set by the installer, or a fault that needs reading. It's often shown with a code. Note the code down, check the user guide, and look up the code before pressing anything.

A warning triangle or exclamation mark is a fault. Common causes are low pressure, a frozen condensate pipe, ignition failure or overheating. Low pressure is the most common one you can fix yourself; see our boiler pressure guide.

Hand holding an open boiler user guide next to the boiler display
Your model's user guide is the definitive key to its symbols and codes.

Reset symbol

A circular arrow, or the word "reset", means the boiler has locked out and is waiting for you to reset it. Reset it once. If it locks out again, don't keep resetting: something is causing it, and repeated resets can hide a fault. Note the code and call a Gas Safe engineer.

Pressure symbol

Many boilers show the water pressure digitally, sometimes with a symbol like a gauge or a "P", or a bar graph. When the system is cold it should usually be between 1 and 2 bar (often around 1 to 1.5). Below 1 bar and many boilers show a warning and stop running. Above 3 bar the pressure relief valve may start dripping outside.

How to find out exactly what your symbols mean

  1. Read the brand and model on the front or the underside of the boiler (or on the data badge inside the flap).
  2. Download the user guide from the manufacturer's website. Search the model name plus "user guide".
  3. Look for the "display" or "control panel" section, which shows every symbol.
  4. If your boiler shows a code, write it down exactly, including any letters.

Our guide to what type of boiler you have helps if you can't find the model name.

FAQs

What does the radiator symbol on a boiler mean?

Central heating is switched on or is being heated. On many models, it flashes while the boiler is actively heating the radiators.

What does the tap symbol on a boiler mean?

Hot water is enabled, or is being heated right now. It often flashes when you run a hot tap on a combi.

What does a snowflake on a boiler mean?

Usually frost protection, or that the heating is turned off for summer and only hot water is on.

What does a spanner symbol mean on a boiler?

A service reminder or a fault. Check for a code and look it up in your user guide.

What does a flame with a cross through it mean?

The boiler failed to light or lost its flame and locked out. Check the gas and condensate pipe, then reset once.

Why is the radiator symbol flashing on my boiler?

On most boilers, it means the boiler is heating the radiators right now. It's normal unless it comes with a fault code.

  • Radiator = heating, tap = hot water, flame = burner lit.
  • Flashing radiator or tap icons usually just mean that function is running.
  • Snowflake = frost protection or heating off for summer.
  • Spanner or warning triangle = check the fault code.
  • Reset once only; repeated lockouts need a Gas Safe engineer.

Was this guide helpful?

Alex Morgan avatar

Written by

How we research and fact-check our guides